Ultimaker

⌘K
  1. Home
  2. /
  3. Docs
  4. /
  5. Ultimaker
  6. /
  7. Factor 4
  8. /
  9. Factor 4 – Peso mas...

Factor 4 – Peso massimo dei pezzi stampati

Note: The information in this article applies to UltiMaker S series and Factor 4 printers.

When printing large and dense parts, an important consideration is the maximum weight the Z motor and Z stage can handle without issues. This is especially relevant for UltiMaker S series and Factor 4 printers, which support a wide range of materials, including heavy, high-density filaments such as metal, glass, and carbon-filled composites.

Given the printers’ generous build volume, it’s natural to wonder how much weight can be safely printed without affecting print quality or risking damage to the printer’s components. In this article, we will outline the recommended weight limits and provide guidance on how to ensure optimal performance when printing heavy parts.

Disclaimer

The information in this article is based on internal testing and general usage guidelines. However, the maximum printable part weight may vary depending on factors such as machine condition, maintenance, environmental conditions, weight distribution, print settings, and material properties. While UltiMaker provides recommendations to help ensure optimal performance, no guarantees can be made regarding specific results. If you experience issues with your printer or believe it is underperforming, please contact UltiMaker Support for further assistance.

Exceeding the maximum recommended part weight can result in a bed drop or motor stall, leading to a non-recoverable print failure. This is especially critical when using dense and heavy specialty filaments, such as metal-filled materials, which are often expensive. Additionally, a bed drop can cause further damage to the printer, including a flooded print head or other mechanical issues. To prevent costly failures and potential machine damage, always follow the recommended weight guidelines and monitor your prints carefully.

Weight guidelines

For reliable printing, follow these weight guidelines:

  • Safe limit: The maximum recommended part weight for a single print is 1.5 kg. This includes both single models and multiple objects placed on the build plate. Under normal conditions, all UltiMaker S series printers and Factor 4 can handle prints up to this weight without issues.
  • Higher weight printing: Under optimal conditions, UltiMaker S series printers and Factor 4 can print parts up to 3 kg. In these cases, it is strongly recommended to center the weight on the build plate, and it is crucial to ensure that all printer components are properly aligned and well-lubricated. For maintenance recommendations, see the section below.
  • Exceeding limits: Printing parts above 4.5 kg is strongly discouraged, as this significantly increases the risk of motor stall and build plate drop. These issues will cause a non-recoverable print failure and may damage the printer.

Important maintenance notes

Regular maintenance of the Z stage components is essential for ensuring smooth movement. This applies to all prints, but is especially important when printing larger or heavier objects. Proper maintenance helps prevent motor stall under higher loads, ensuring reliable performance.

Maintaining the Z stage involves regular cleaning and relubrication of the Z shafts and the trapezoidal lead screw of the Z motor.

Z shafts

The Z shafts are the smooth axles on either side of the Z stage. The base plate contains linear bearings that allow the Z stage to move up and down along these shafts. To ensure smooth operation, the shafts should be lubricated with machine or mineral oil. Under light to normal use, cleaning and relubrication are recommended every six months. However, if the printer is used frequently or for printing heavy objects, more frequent maintenance is advised.

If the shafts become dirty or dry, the bearings may stick, leading to uneven movement or increased strain on the Z motor. Regular maintenance helps prevent these issues, ensuring consistent and reliable performance. Machine oil is included in the S series accessory boxes and mineral oil is included in the Factor 4 Maintenance Kit.

Tip: Learn more about lubricating the Z shafts here for S series and Factor 4.

Z motor

The Z motor and trapezoidal lead screw work together to control the vertical movement of the build plate. As the Z motor rotates, the lead screw drives the lead nut in the Z stage base plate, precisely raising or lowering the build plate. This system ensures smooth, accurate layer positioning, which is essential for high-quality prints.

The lead screw is lubricated with grease. Over time, particles from the printing process or the environment may accumulate in the grease which can put additional strain on the motor. Approximately once every three months, check, clean, and relubricate the Z motor’s lead screw. Use the grease (Eurol) included in the S series accessory boxes and Factor 4 Maintenance Kit.

Tip: Learn more about lubricating the Z motor’s lead screw here for S series and Factor 4.

Need further support?

If you have any questions about printing heavy parts, need guidance on printing strategies, or want more information about printer maintenance, please contact UltiMaker Support. Our support team is happy to provide further assistance.